Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
Presented here down the page you can discover a good deal of very good data when it comes to How to Install a Bathtub Yourself.
Setting up a bathtub isn't precisely brain surgery, but it does need solid plumbing, woodworking, and often, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably difficult task. If the old tub is readily obtainable, the job can relocate rapidly; if you need to open a wall surface to get rid of the old bathtub and also place the brand-new bathtub, the job is much harder. In either instance, the task is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and set in the new one. Ensure you have qualified on your own for the task and also fit trying it. As opposed to employing a professional to take control of a halfway-completed job, it is better to consider utilizing one before you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will certainly assist you set up a new tub in your restroom if you have currently gotten a new bathtub as well as don't need to alter the setup of your previous supply of water pipes.
Your devices and product list need to make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you should do is separate the water system. After doing so, activate the faucets to drain any water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome due to the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have actually been removed, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin guaranteeing that the washers are in place between the faucet and also the sink. Protect the tap in place with the maker supplied backnut. Once the tap is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet ports. The previous type needs to be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing both wooden boards under its feet, position the bath tub in the required placement. The wooden boards are helpful in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the spirit level and also readjusting the feet on the tub until the spirit level reads degree.
To mount taps, fit all-time low of the furthest versatile faucet port to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water and also examine all joints as well as new pipework for leaks and also tighten them if essential. Fill the bath tub as well as additionally inspect the overflow electrical outlet as well as the normal outlet for leaks.
Ultimately, fix the bath paneling as defined in the producer's user's manual. Tiling and also securing around the tub ought to wait until the bathtub has been made use of at least once as this will certainly resolve it into its last placement.
Preparing for the Installation
Firstly, the sustaining structure supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps system to stop strain on the bathtub.
Fit the flexible faucet adapters to the bottom of the two faucets using 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you utilize every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a rigid seal, creating the water to permeate the wall in between the bath and the tiling, bring about difficulties with wetness and also feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components and also fittings. They are marketed in tubes and cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to permit the activity experienced when the bathtub remains in usage. The sealant can split rather very early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very taken with How to Install a Bathtub Yourself and I really hope you appreciated the entire blog entry. Are you aware of someone else who is interested in the topic? Please feel free to promote it. Thank-you for going through it.
Emergency leaks? Professional help here. Report this page